Complete Baling and Shredding System Like New

Complete Baling and Shredding System - Like New Condition

Only 65 Hours on System

Entire Security Shredding and Baling System. Full package includes a Shred Tech Model ST-15E Shredder,

64/96 Gallon standard Cart Tipper,

and a Unimaster Model UMA 150 Dust Collector.

Less than 2 years old with very low hours. Originally sold new in 2009 for $195,407.

Priced for Very Quick Sale!

System complete as pictured - less Baler

$38,000.00 FOB Lansdale, PA

Contact our Sales Department for Baler options.

CLICK HERE To See More Horizontal Balers For Sale

Specifications:

1) APPLICATION INFORMATION

Description: Designed to dump standard 64 gallon and 96 gallon collection totes of Paper products, microfiche, confidential documents, CPO, books, binders, sheet stock, checks, etc. into a shredder bin for automatic shredding. Shredded particles are conveyed up to an automatic baler for compression into market size bales. . Factory rated to destroy material at approx. 3000 lbs. per hour.

Shred Size - Approx. 5/8" cross cut, industry standard

2) EQUIPMENT

A) SHRED-TECH Model ST-15E INDUSTRIAL SHREDDER SYSTEM

Cutting Chamber - 13" x 20 7/8” Opening, Two hexagonal, counter rotating shafts (2-5/8" across flats), Protective bulkhead walls at both ends of chamber to prevent migration of contaminants into bearings and seals

Knives - - Number of knives: 32, width: 5/8” (16 mm) Hub Knife, Knife diameter: 6 ¾”, Number of teeth per knife: Multi, offset for quick material capture, material: heat-treated alloy steel, Contoured cleaning fingers, Shaft center distance: 5 7/8”,

Drive System - 30 HP gear reduced motor, 460V/3Ph/60Hz, Flange connected to shredder gearbox, Two stage gear reduction, Fast/Slow Shaft Speed - 30 / 25 rpm, Maximum Tooth Force - 32,460 lbs./ft

B) BALER - Contact out Sales Department for sizing for your application. Options from $10,000-$70,000

C) 64 / 96 GALLON CART TIPPER

Single bucket lifter heavy-duty design, Chain actuation, 200 lbs. (max) capacity, Gear motor drive and clutch, Complete support frame and safety enclosure with safety, E-stop on door, Designed to accept 64 & 96 gallon North American totes, Operational Controls integrated into main shredder panel

D) SUPPORT STAND

Structural tube construction, all welded construction, Stand designed to position shredder on 35 degree slope, Fully welded c/w footpad mounting, Discharge chute to conveyor as required

E) VIBRATORY FEED HOPPER

Vibratory shaker to control feed rate to shredder as required, 1/3 HP 460V/3Ph/60Hz, Aluminum plate construction, oversized capacity designed to hold the volume of one 96 gallon tote, 54” x 34” opening, 37” high (approx.), Deigned to mate with shredder opening and tipper, Flange mounted to shredder

F) SHREDDER DISCHARGE CONVEYOR

Slider Bed Conveyor, Pulley Diameter: 3 1/2", Lower Horizontal Length: 4’, Incline Length: 10’” approx., Upper Horizontal Length: 1'6", Degree Of Curves: 45 Deg, Frame Construction: 12 Ga. Bolt-Together, Effective Width: 18", Belt: Rmv 150 X-Rigid Black Belting, Cleats: 1 1/2" @ 24" Centers, Side Skirts: 8" High, Full covers on incline for dust control, Belt Return: Bottom Pan, Belt Speed: 40 Fpm Fixed, Drive: 1 Hp 460V/3Ph/60Hz, - Controls in main panel

G) CONTROL PANEL

NEMA enclosure, 460V/3Ph/60Hz, 5000 amp maximum ground fault, Keyed “power” switch, Illuminated function/indicating buttons for shredder operation, Fused lockable disconnect, All necessary fuses, contactors and thermal overloads, Direct across the line starting, Integral 120 volt, AC control circuit, Programmable logic controller for shredder operation and monitoring, Run time hour meter

H) BALER HOPPER EXTENSION

Approx 40” W x 21” H x 26” D, PVC strip curtain for dust containment, Dust collector pipe port on top, Mating flange to Maren baler hopper, Designed to fit shredder discharge conveyor

I) Unimaster Model UMA 150 Dust Collection System

Filter Area: 150 square feet, Filter Material: 8 oz. polyester : 950 cfm @ 7"wg. 70°F. 0 foot elevation, Application: Paper dust, 2:01 Housing: Unit is constructed of 16 gauge steel rated at –16” w.g. Lift off hinged doors allow easy access to filter and fan sections for inspection and maintenance, Finish: mild steel with a baked on powder finish on interior and exterior panels, Filter Element: multi-envelope single piece design with flexible wire mesh supporting inserts, Single piece design minimizes the sealing requirements and improves efficiency, Efficiency: Unit is 99% efficient by weight with seasoned bags, Filter Cleaning: Filter cleaning is accomplished by a 1/4 HP, TENV, 1175 RPM shaker motor connected to a shaker bar via an eccentric. The shaker motor is activated for 35 seconds each time the fan is shut down. Hopper & Dust Storage: Hopper is connected via a flexible sleeve to a one 55-gallon drum supplied w/ unit, Integral Fan: An integral fan is located on the clean air side of the unit is a Backward Incline type directly driven by a 3450 RPM, 5 HP, TEFC motor, Cleaning Controls: A Controller is supplied for starting of fan and automatic operation of filter shaker motor. The controller includes fan and shaker motor contactors with overloads, control circuit transformer, timer for automatic activation of shaker motor and NEMA 12 enclosure with Start and Clean pushbuttons.

3) Optional - Brand New Truck Unloading Conveyor Package

Special low profile conveyor designed for easy unloading your shredding trucks directly into baler. Includes full dust enclosure, Ask our Sales department for full details. Added Price $45,000.00

 CLICK HERE To See More Horizontal Balers For Sale

Click here or Call us for more info on this Machine